Translations:Einzugsgebiet/21/en - Versionsgeschichte

Froehlich am 25. November 2020 um 10:01 Uhr

2020-11-25T10:01:27Z

← Nächstältere Version		Version vom 25. November 2020, 12:01 Uhr
Zeile 1:		Zeile 1:
	Depression losses (MV) are specified by the user. The default and simultaneously maximum value in the model is 4 mm.		Depression losses (MV) are specified by the user. The default and simultaneously maximum value in the model is 4 mm.
	Depression losses represent an average value for an sloped surface. Since depressions are not evenly distributed and runoff already begins before all depressions are completely filled, it is assumed that		Depression losses represent an average value for an sloped surface. Since depressions are not evenly distributed and runoff already begins before all depressions are completely filled, it is assumed that
	* 1/3 of the impermeable area has a reduced depression loss of 1/3&~~cdot~~;MV		* 1/3 of the impermeable area has a reduced depression loss of 1/3⋅MV
	* 1/3 of the impermeable area has the average depression loss of MV		* 1/3 of the impermeable area has the average depression loss of MV
	* 1/3 of the impermeable area has an increased depression loss of 5/3&~~cdot~~;MV		* 1/3 of the impermeable area has an increased depression loss of 5/3⋅MV
	Therefore, runoff already occurs when the precipitation reduced by the evaporation rate exceeds the wetting loss and 1/3 of the depression losses (in case of dry starting conditions). The assumptions described above are shown as a schematic in the following figure.		Therefore, runoff already occurs when the precipitation reduced by the evaporation rate exceeds the wetting loss and 1/3 of the depression losses (in case of dry starting conditions). The assumptions described above are shown as a schematic in the following figure.

Froehlich am 25. November 2020 um 09:56 Uhr

2020-11-25T09:56:06Z

← Nächstältere Version		Version vom 25. November 2020, 11:56 Uhr
Zeile 1:		Zeile 1:
	~~The trough loss~~ (MV) is specified by the user. The ~~standard~~ and simultaneously maximum value in the model is 4 mm.		Depression losses (MV) are specified by the user. The default and simultaneously maximum value in the model is 4 mm.
	~~The trough loss represents the~~ average value for an ~~sloping~~ surface. ~~However, since the troughs~~ are not evenly distributed and~~, as experience shows, drainage~~ begins before ~~the complete filling of the troughs has been reached everywhere~~, it is assumed that		Depression losses represent an average value for an sloped surface. Since depressions are not evenly distributed and runoff already begins before all depressions are completely filled, it is assumed that
	* 1/3 of the ~~sealed surface~~ has a reduced ~~trough~~ loss of 1/3-MV		* 1/3 of the impermeable area has a reduced depression loss of 1/3&cdot;MV
	* 1/3 of the ~~sealed~~ area the average ~~trough~~ loss of ~~3/3-~~MV		* 1/3 of the impermeable area has the average depression loss of MV
	* 1/3 of the ~~sealed surface~~ has an increased ~~trough~~ loss of 5/3-MV		* 1/3 of the impermeable area has an increased depression loss of 5/3&cdot;MV
	~~has.~~ Therefore, runoff already occurs when the precipitation reduced by the evaporation rate exceeds the wetting loss and 1/3 of the ~~trough loss~~ (in case of dry ~~history~~). The assumptions above are ~~schematically sketched~~ in the following figure.		Therefore, runoff already occurs when the precipitation reduced by the evaporation rate exceeds the wetting loss and 1/3 of the depression losses (in case of dry starting conditions). The assumptions described above are shown as a schematic in the following figure.

Ferrao: Die Seite wurde neu angelegt: „The trough loss (MV) is specified by the user. The standard and simultaneously maximum value in the model is 4 mm. The trough loss represents the average value…“

2020-10-08T14:37:23Z

Die Seite wurde neu angelegt: „The trough loss (MV) is specified by the user. The standard and simultaneously maximum value in the model is 4 mm. The trough loss represents the average value…“

Neue Seite

The trough loss (MV) is specified by the user. The standard and simultaneously maximum value in the model is 4 mm.
The trough loss represents the average value for an sloping surface. However, since the troughs are not evenly distributed and, as experience shows, drainage begins before the complete filling of the troughs has been reached everywhere, it is assumed that
* 1/3 of the sealed surface has a reduced trough loss of 1/3-MV
* 1/3 of the sealed area the average trough loss of 3/3-MV
* 1/3 of the sealed surface has an increased trough loss of 5/3-MV
has. Therefore, runoff already occurs when the precipitation reduced by the evaporation rate exceeds the wetting loss and 1/3 of the trough loss (in case of dry history). The assumptions above are schematically sketched in the following figure.