Transportstreckenfenster/en: Unterschied zwischen den Versionen

Aus TALSIM Docs
Keine Bearbeitungszusammenfassung
Keine Bearbeitungszusammenfassung
 
(24 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt)
Zeile 19: Zeile 19:


In the calculation method section, the translation and retention behavior calculation method is set for the [[Special:MyLanguage/Transportstrecke|transport reach element]]. There are four options:
In the calculation method section, the translation and retention behavior calculation method is set for the [[Special:MyLanguage/Transportstrecke|transport reach element]]. There are four options:
* Pure translation (without retention)
* Translation (pure translation without retention)
* Pipe
* Pipe (gravitational)
* Open channel with defined cross-section geometry
* Open channel (with defined cross section geometry)
* Characteristic curve (water level - cross-sectional area - outflow)
* Capacity function (via characteristic curve: water level - cross-sectional area - outflow)




===Translation===
===Translation===


If the calculation method [[Special:MyLanguage/Transportstrecke#Translation|Translation]] is selected, only the translation time parameter is entered. The default setting is 1440 min, i.e. one day.
If the calculation method [[Special:MyLanguage/Transportstrecke#Translation|translation]] is selected, only the translation time parameter is entered. The default setting is 1440 min, i.e. one day.


[[Datei:Transportstreckenfenster Berechnungsweise Translation_EN.PNG|Datei:Transportstreckenfenster Berechnungsweise Translation_EN.PNG]]
[[Datei:Transportstreckenfenster Berechnungsweise Translation_EN.PNG|Datei:Transportstreckenfenster Berechnungsweise Translation_EN.PNG]]




===Pipeline===
===Pipe===


For the calculation of the transport reach as a [[Special:MyLanguage/Transportstrecke#Freispiegel-Rohrleitung|pipeline]], information on the diameter, the bottom gradient and the operating roughness are required. If a pipe with a non-circular cross-section is to be calculated, the hydraulic diameter and the profile area (cross-section area when fully filled) are specified instead of the circular diameter.
For the calculation of the transport reach as a [[Special:MyLanguage/Transportstrecke#Freispiegel-Rohrleitung|pipeline]], information on the diameter, the slope and the roughness of the pipe are required. If the transport reach for a pipe with non-circular cross section is to be calculated, the hydraulic diameter and the profile area (whole cross section when fully filled) are specified instead of the circular diameter.


[[Datei:Transportstreckenfenster Berechnungsweise Rohrleitung_EN.PNG|Datei:Transportstreckenfenster Berechnungsweise Rohrleitung_EN.PNG]]
[[Datei:Transportstreckenfenster Berechnungsweise Rohrleitung_EN.PNG|Datei:Transportstreckenfenster Berechnungsweise Rohrleitung_EN.PNG]]




===Open channel===
===Open Channel===


The calculation option [[Special:MyLanguage/Transportstrecke# Offenes Gerinne mit Angabe eines Querprofiles|open channel]] requires the specification of a cross section, defined by a height, and the corresponding widths on the right and left. The Strickler values (kst) are entered separately for the right and left bank and it can be specified whether the support point is the channel itself or the foreland.
The calculation option [[Special:MyLanguage/Transportstrecke# Offenes Gerinne mit Angabe eines Querprofiles|open channel]] requires the specification of a cross section, defined by a height, and the corresponding widths on the right and left. The Strickler values (kst) are entered separately for the right and left bank and it can be specified whether the supporting point is the channel itself or the foreland.
For this purpose, the values can be simply written into the table area and it is possible to navigate through the table or to insert new lines with the arrow keys, the tab key or the enter key.
For this purpose, the values can be simply written into the table area and it is possible to navigate through the table or to insert new lines with the arrow keys, the tab key or the enter key.


Zeile 47: Zeile 47:


* add new supporting points to the end of the table
* add new supporting points to the end of the table
* insert new supporting points  in front of the currently marked supporting point
* insert new supporting points  in front of the currently marked support point
* edit a supporting point in an extra window
* edit a supporting point in an extra window
* delete the marked supporting point
* delete the marked supporting point
Zeile 55: Zeile 55:
[[Datei:Transportstreckenfenster Berechnungsweise offenes Gerinne_EN.PNG|Datei:Transportstreckenfenster Berechnungsweise offenes Gerinne_EN.PNG]]
[[Datei:Transportstreckenfenster Berechnungsweise offenes Gerinne_EN.PNG|Datei:Transportstreckenfenster Berechnungsweise offenes Gerinne_EN.PNG]]


If you have entered a cross profile in the table, you can have it displayed as a graphic by checking the checkbox ''Graphic''.
If you have entered a cross section in the table, you can have it displayed as a graphic by checking the checkbox ''Display''.


[[Datei:Transportstreckenfenster Berechnungsweise offenes Gerinne gefüllt_EN.PNG|Datei:Transportstreckenfenster Berechnungsweise offenes Gerinne gefüllt_EN.PNG]][[Datei:Transportstreckenfenster Grafik Querprofil_EN.PNG|Datei:Transportstreckenfenster Grafik Querprofil_EN.PNG]]
[[Datei:Transportstreckenfenster Berechnungsweise offenes Gerinne gefüllt_EN.PNG|Datei:Transportstreckenfenster Berechnungsweise offenes Gerinne gefüllt_EN.PNG]][[Datei:Transportstreckenfenster Grafik Querprofil_EN.PNG|Datei:Transportstreckenfenster Grafik Querprofil_EN.PNG]]




===Characteristic Curve===
===Capacity Function===


The calculation option [[Special:MyLanguage/Transportstrecke#Kennlinie (Wasserspiegel – Querschnittsfläche – Abfluss)|characteristic curve]] requires the input of a discharge curve defined by several interpolation points consisting of water level, cross-sectional area and associated discharge.
The calculation option [[Special:MyLanguage/Transportstrecke#Kennlinie (Wasserspiegel – Querschnittsfläche – Abfluss)|capacity function]] requires the input of a discharge curve defined by several supporting points including water level, cross-sectional area and the corresponding discharge.


For this purpose, the values can simply be written into the table area and you can navigate through the table or insert new rows using the arrow keys, the Tab key or the Enter key.
For this purpose, the values can simply be written into the table area and you can navigate through the table or insert new rows using the arrow keys, the tab key or the enter key.


Alternatively, the function bar [[Datei:Funktionsleiste Tabelle editieren.PNG|Datei:Funktionsleiste Tabelle editieren.PNG]] can be used to edit the table. You can:  
Alternatively, the function bar [[Datei:Funktionsleiste Tabelle editieren.PNG|Datei:Funktionsleiste Tabelle editieren.PNG]] can be used to edit the table. You can:  
Zeile 77: Zeile 77:
[[Datei:Transportstreckenfenster Berechnungsweise Kennlinie_EN.PNG|Datei:Transportstreckenfenster Berechnungsweise Kennlinie_EN.PNG]]
[[Datei:Transportstreckenfenster Berechnungsweise Kennlinie_EN.PNG|Datei:Transportstreckenfenster Berechnungsweise Kennlinie_EN.PNG]]


If you have entered a discharge curve in the table, you can have it displayed as a graphic by checking the ''Graphic'' box.
If you have entered a discharge curve in the table, you can have it displayed as a graphic by checking the ''Display'' box.


[[Datei:Transportstreckenfenster Berechnungsweise Kennlinie gefüllt_EN.PNG|Datei:Transportstreckenfenster Berechnungsweise Kennlinie gefüllt_EN.PNG]][[Datei:Transportstreckenfenster Grafik Kennlinie_EN.PNG|Datei:Transportstreckenfenster Grafik Kennlinie_EN.PNG]]
[[Datei:Transportstreckenfenster Berechnungsweise Kennlinie gefüllt_EN.PNG|Datei:Transportstreckenfenster Berechnungsweise Kennlinie gefüllt_EN.PNG]][[Datei:Transportstreckenfenster Grafik Kennlinie_EN.PNG|Datei:Transportstreckenfenster Grafik Kennlinie_EN.PNG]]

Aktuelle Version vom 26. Januar 2021, 10:32 Uhr

Sprachen:

The properties for transport reach can be opened by double-clicking on the element symbol in the system plan Systemelement003.png or by right-clicking → Properties. In the upper part of the window there are three buttons: one for saving Datei:Button_speichern.PNG, one for applying the parameters and one for the settings of transport reach elements in the same database (i.e. also from other variants and projects) Datei:Button_Werte_übernehmen.PNG. In addition, there is a button for closing the window. It is important to know that the transport reach window saves automatically when closing via this button.

Datei:Transportstreckenfenster_leer_EN.PNG


Properties

The length of the transport reach and the starting value for the flow are entered in the "Properties" section.

File:Transportstreckenfenster_Eigenschaften_EN.PNG


Calculation Method

In the calculation method section, the translation and retention behavior calculation method is set for the transport reach element. There are four options:

  • Translation (pure translation without retention)
  • Pipe (gravitational)
  • Open channel (with defined cross section geometry)
  • Capacity function (via characteristic curve: water level - cross-sectional area - outflow)


Translation

If the calculation method translation is selected, only the translation time parameter is entered. The default setting is 1440 min, i.e. one day.

Datei:Transportstreckenfenster Berechnungsweise Translation_EN.PNG


Pipe

For the calculation of the transport reach as a pipeline, information on the diameter, the slope and the roughness of the pipe are required. If the transport reach for a pipe with non-circular cross section is to be calculated, the hydraulic diameter and the profile area (whole cross section when fully filled) are specified instead of the circular diameter.

Datei:Transportstreckenfenster Berechnungsweise Rohrleitung_EN.PNG


Open Channel

The calculation option open channel requires the specification of a cross section, defined by a height, and the corresponding widths on the right and left. The Strickler values (kst) are entered separately for the right and left bank and it can be specified whether the supporting point is the channel itself or the foreland. For this purpose, the values can be simply written into the table area and it is possible to navigate through the table or to insert new lines with the arrow keys, the tab key or the enter key.

Alternatively, the function bar Datei:Funktionsleiste Tabelle editieren.PNG can be used to edit the table. You can:

  • add new supporting points to the end of the table
  • insert new supporting points in front of the currently marked support point
  • edit a supporting point in an extra window
  • delete the marked supporting point

By right-clicking on the table, a menu appears which can also be used to add, insert and delete rows.

Datei:Transportstreckenfenster Berechnungsweise offenes Gerinne_EN.PNG

If you have entered a cross section in the table, you can have it displayed as a graphic by checking the checkbox Display.

Datei:Transportstreckenfenster Berechnungsweise offenes Gerinne gefüllt_EN.PNGDatei:Transportstreckenfenster Grafik Querprofil_EN.PNG


Capacity Function

The calculation option capacity function requires the input of a discharge curve defined by several supporting points including water level, cross-sectional area and the corresponding discharge.

For this purpose, the values can simply be written into the table area and you can navigate through the table or insert new rows using the arrow keys, the tab key or the enter key.

Alternatively, the function bar Datei:Funktionsleiste Tabelle editieren.PNG can be used to edit the table. You can:

  • add new supporting points to the end of the table
  • insert new supporting points in front of the currently marked supporting point
  • edit a supporting point in an extra window
  • delete the marked supporting point

By right-clicking on the table, a menu appears which can also be used to add, insert and delete rows.

Datei:Transportstreckenfenster Berechnungsweise Kennlinie_EN.PNG

If you have entered a discharge curve in the table, you can have it displayed as a graphic by checking the Display box.

Datei:Transportstreckenfenster Berechnungsweise Kennlinie gefüllt_EN.PNGDatei:Transportstreckenfenster Grafik Kennlinie_EN.PNG